Quadcopter Frame Kit With 4 x A2212 KV1000 Brushless Motor and 4 x 30A ESC and 2 Pair 1045 Propeller (With CT6B Radio Model RC Transmitter & Receiver)

PRODUCT OVERVIEW:

• Materials: glass fiber + polyamide-nylon


• Frame Weight: 280g.


• Height: 55mm


• Colored arms for orientation to keep you flying in the right direction.


• Power distribution board included in this item(inbuilt PCB).


• Pre-threaded brass sleeves for all frame bolts.


• Large mounting tabs on the main frame bottom plate for easy camera mounting.

A2212/10T/13T 1000KV BRUSHLESS MOTOR WITH SOLDERED CONNECTOR

• KV: 1000


• MAX Efficiency: 80%


• MAX Efficiency Current: 4-10A (>75%)


• Current Capacity: 12A / 60s


• No Load Current: 10 V : 0.5 A

Orange HD Propellers 1045(10X4.5) ABS DJI Black (1CW+1CCW)

• Weight (1 pair): 22 gm.


• Shaft diameter (mm): 7-(Flat Side) and 8-(Round Side)


• Total length: 10 inches (254 mm)


• ABS Material


• Very strong and lightweight.

30A BLDC ESC Electronic Speed Controller

• Current: 30-40 A


• Constant Current: 30 A Maximum (40A for maximum 10sec)


• BEC: 3 A


• Good Speed Control


• Excellent Stability Control

1. APM 2.8 Multicopter Flight Controller 2.5 2.6 Upgraded Built-in Compass for FPV RC Drone Aircraft
   
   
   
   1. Needle: straight.
   
   
   2. Power supply: LP2985-3.3.
   
   
   3. Max voltage: 16V.
   
   
   4. Add a 47uF tantalum capacitor.
   
   
   5. Port: MUX (UART0, UART2, mnnI2, and OSD are optional, OSD is the defaulted output).
   
   
   6. Arduino Compatible!
   
   
   7. Includes 3-axis gyro, accelerometer, along with a high-performance barometer
   
   
   8. Onboard 4 MegaByte Dataflash chip for automatic data logging.
   
   
   9. Optional off-board GPS, a uBlox LEA-6H module with Compass.
   
   
   
   


2. 
   

   CT6B FlySky 2.4Ghz 6CH Transmitter w/FS-R6B Receiver Mode 2

   
   
   1. STICK MODE: Left hand or Right hand
   
   
   2. MODULATION: Frequency Modulation
   
   
   3. ANTENNA LENGTH: 115cm/26mm
   
   
   4. CODE TYPE: PPM/GFSK
   
   
   5. POWER: 12V DC
   
   
   6. RF POWER: Less than 0.8W
   
   
   7. CHANNELS: 6 channels
   
   
   8. High receiving sensitivity.
   
   
   9. 8 model memory, digital control.
   
   
   
   

--

This is ARF Quadcopters Economy Combo Kit which will help you become a quadcopters pilot. Simply get out the soldering iron, put on your safety goggles and began soldering. This Economy kit has very good products and is available at affordable cost.

For someone new to the multirotor hobby, putting together your first quadcopters parts list and bringing them home can be extremely daunting. Trying to figure out what to buy and what parts will work together is tough, especially for people who don’t come from a background in radio controlled planes or helicopters. For the people who want to build a quadcopters but don’t know where to start. It can be frustrating trying to sort things and figure out what to do.

We’ve heard from a lot of peoples who are in similar positions and this bunch of products is designed to spell out exactly what you need for your quadcopter build. While we will recommend a complete list of specific parts that we have tested for a complete quadcopter build, the main purpose providing an ARF Quadcopters Economy Combo Kit needed to build a quadcopter.

Q450 Quadcopter Frame – PCB Version Frame Kit with Integrated PCB

Every quadcopter or other multirotor aircraft needs a frame to house all the other components. Things to consider here are weight, size, and materials. This Q450 QUADCOPTER FRAME is a well thought out 450mm quad frame built from quality materials. The main frame is glass fiber while the arms are constructed of ultra-durable polyamide nylon. This version 3 of the Q450 QUADCOPTER FRAME features integrated PCB connections for direct soldering of your ESCs. This eliminates the need for a power distribution board or messy multi-connectors keeping your electronics layout very tidy. V3 also comes with stronger molded arms over V1 and V2, so no more arm breakage at the motor mounts on a hard landing

A2212/10T/13T 1000kv Brushless Motor with Soldered Connector

The motors have an obvious purpose: to spin the propellers. There are many motors suitable for quadcopters, and this A2212/10T/13T 1000KV BRUSHLESS MOTOR WITH SOLDERED CONNECTOR is one of them which is included in this kit. Motors are rated by kilovolts and the higher the kV rating, the faster the motor spins at a constant voltage. The A2212/10T/13T 1000KV BRUSHLESS MOTOR WITH SOLDERED CONNECTOR motor for the airplane aircraft quadcopter. A2212 / 13T 1000KV BRUSHLESS MOTOR OUTRUNNER with 80% maximum efficiency, 4-10A max efficiency current, and 12A / 60s current capacity.

30A BLDC ESC Electronic Speed Controller

The electronic speed control, or ESC, is what tells the motors how fast to spin at any given time. You need four ESCs for a quadcopter, one connected to each motor. The ESCs are then connected directly to the battery. SIMONK 30A BLDC ESC ELECTRONIC SPEED CONTROLLER is specifically made for quadcopters and multi-rotors and provides faster and better motor speed control giving better flight performance compared to other available ESCs. SIMONK 30A BLDC ESC ELECTRONIC SPEED CONTROLLER can drive motors which consume up to 30A current. It works on 2S-3S LiPo batteries. It has an onboard BEC which provides regulated 5V(2A max draw) to power the flight controller and other onboard modules. It can be used to control our brushless motors with a 2S-3S LiPo (make sure motor doesn’t draw more than 30A). This particular ESC is recommended with A2212 brushless motor (1000kv, 1400kv, 2200kv).

APM 2.8 Multicopters Flight Controller 2.5 2.6 Upgraded Built-in Compass for FPV RC Drone Aircraft

The flight control board is the ‘brain’ of the quadcopter. It houses the sensors such as gyroscopes and accelerometers that determine how fast each of the quadcopters motors spin. Flight control boards range from simple to highly complex. APM 2.8 Multicopter Flight Controller 2.5 2.6 Upgraded Built-in Compass for FPV RC Drone Aircraft is the new APM 2.8 flight controller. The sensors are exactly the same as the APM 2.6 flight controller; however, this has the option to use the built-in compass, or external compass via a jumper. This makes the APM 2.8 ideal for use with multi-copters and rovers.

The APM 2.8 Multicopters Flight Controller is a complete open source autopilot system and the bestselling technology that won the prestigious Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints.

CT6B FlySky 2.4Ghz 6CH Transmitter w/FS-R6B Receiver Mode 2

The radio transmitter and receiver allow you to control the quadcopter but you will need at least four channels for a basic quadcopter. We recommend using a radio with 6 channels, so there is more flexibility.

CT6B FLYSKY 2.4GHZ 6CH TRANSMITTER is the popular 6 Channel Radio CT6B manufactured by FlySky. CT6B FLYSKY 2.4GHZ 6CH TRANSMITTER is an entry-level 2.4 GHz radio system offering the reliability of 2.4 GHz signal technology and a receiver with 6 channels.

CT6B FLYSKY 2.4GHZ 6CH TRANSMITTER radio is a value for money, entry level 6 channel transmitter, ideal for quadcopters and multi-copters that require the 6ch operation. This radio has two retract switches and proportional flap dials in easy reach for channels 5 and 6.

It can be powered by 8 x AA Size Batteries or a 12V Power Supply. It comes with a trainer port to help beginners learn flying. It can be configured by connecting it to the computer. Use the T6config software to configure your radio on a computer